Up to this point inductance and capacitance have been explained individually in ac circuits. The rest of this part will concern the combination of inductance, capacitance, and resistance in ac circuits.
To explain the various properties that exist within ac circuits, the series RLC circuit will be used. Figure (4) is the schematic diagram of the series RLC circuit. The symbol shown in figure 4-4 that is marked E is the general symbol used to indicate an ac voltage source.
Series RLC circuit
The effect of inductive reactance is to cause the current to lag the voltage, while that of capacitive reactance is to cause the current to lead the voltage. Therefore, since inductive reactance and capacitive reactance are exactly opposite in their effects, what will be the result when the two are combined? It is not hard to see that the net effect is a tendency to cancel each other, with the combined effect then equal to the difference between their values. This resultant is called REACTANCE; it is represented by the symbol X; and expressed by the equation X = XL – XC or X = XC – XL. Thus, if a circuit contains 50 ohms of inductive reactance and 25 ohms of capacitive reactance in series, the net reactance, or X, is 50 ohms – 25 ohms, or 25 ohms of inductive reactance.
For a practical example, suppose you have a circuit containing an inductor of 100 µH in series with a capacitor of .001 µF, and operating at a frequency of 4 MHz What is the value of net reactance, or X?
Given f = 4MHz, L = 100μH, C =0.001μF
Solution: XL = 2πfL
= 6.28 x 4MHz x 100μH = 2512 Ω
Xc = 1/2πfC
= 1/6.28 x 4MHz x 0.001μF
X = XL – XC
X = 24722Ω (inductive)
From your study of inductance and capacitance you know how inductive reactance and capacitive reactance act to oppose the flow of current in an ac circuit. However, there is another factor, the resistance, which also opposes the flow of the current. Since in practice ac circuits containing reactance also contain resistance, the two combine to oppose the flow of current. This combined opposition by the resistance and the reactance is called the IMPEDANCE, and is represented by the symbol Z.
Since the values of resistance and reactance are both given in ohms, it might at first seem possible to determine the value of the impedance by simply adding them together. It cannot be done so easily, however. You know that in an ac circuit which contains only resistance, the current and the voltage will be in step (that is, in phase), and will reach their maximum values at the same instant. You also know that in an ac circuit containing only reactance the current will either lead or lag the voltage by one-quarter of a cycle or 90 degrees. Therefore, the voltage in a purely reactive circuit will differ in phase by 90 degrees from that in a purely resistive circuit and for this reason reactance and resistance are combined by simply adding them.
When reactance and resistance are combined, the value of the impedance will be greater than either. It is also true that the current will not be in step with the voltage nor will it differ in phase by exactly 90 degrees from the voltage, but it will be somewhere between the in-step and the 90-degree out-of-step conditions. The larger the reactance compared with the resistance, the more nearly the phase difference will approach 90°. The larger the resistance compared to the reactance, the more nearly the phase difference will approach zero degrees.
If the value of resistance and reactance cannot simply be added together to find the impedance, or Z, how is it determined? Because the current through a resistor is in step with the voltage across it and the current in a reactance differs by 90 degrees from the voltage across it, the two are at right angles to each other. They can therefore be combined by means of the same method used in the construction of a right-angle triangle.
Assume you want to find the impedance of a series combination of 8 ohms resistance and 5 ohms inductive reactance. Start by drawing a horizontal line, R, representing 8 ohms resistance, as the base of the triangle.
Then, since the effect of the reactance is always at right angles, or 90 degrees, to that of the resistance, draw the line XL, representing 5 ohms inductive reactance, as the altitude of the triangle. This is shown in figure (5). Now, complete the hypotenuse (longest side) of the triangle. Then, the hypotenuse represents the impedance of the circuit.
Vector diagram showing relationship of resistance, inductive reactance, and impedance in a series circuit.
One of the properties of a right triangle is:
(hypotenuse)2 = (base)2 + (altitude)2
Hypotenuse = √(base)2 (altitude)2
Applied to impedance, this becomes,
(impedance)2 = (resistence)2 + (reactance)2
Impedance = √(resistance)2 + (reactance)2
Impedance = √(resistance) 2 + (reactrance)2
Z = √R2 + X2
Now suppose you apply this equation to check your results in the example given above.
Given : R = 8Ω, XL =5Ω
Solution : Z = √R2 + XL 2
= √(8Ω)2 + (5Ω)2
= √64 + 25
= √89Ω = 9.4Ω
When you have a capacitive reactance to deal with instead of inductive reactance as in the previous example, it is customary to draw the line representing the capacitive reactance in a downward direction. This is shown in figure (6). The line is drawn downward for capacitive reactance to indicate that it acts in a direction opposite to inductive reactance which is drawn upward. In a series circuit containing capacitive reactance the equation for finding the impedance becomes:
Z = √R2 + XC2
In many series circuits you will find resistance combined with both inductive reactance and capacitive reactance. Since you know that the value of the reactance, X, is equal to the difference between the values of the inductive reactance, XL, and the capacitive reactance, XC, the equation for the impedance in a series circuit containing R,XL, and XCthen becomes:
Z = √R2 + (XL – XC)2 or Z = √R2 + X2
Note: The formulas Z = √R2 + XC2, Z = √R2 + X2 and Z = √R2 + XL 2 can be used to calculate Z only if the reisitance and reactance are connected in series.
In the above expressions, you will see the method which may be used to determine the impedance in a series circuit consisting of resistance, inductance, and capacitance.
Assume that 10 ohms inductive reactance and 20 ohms capacitive reactance are connected in series with 40 ohms resistance. Let the horizontal line represent the resistance R. The line drawn upward from the end of R, represents the inductive reactance, XL. Represent the capacitive reactance by a line drawn downward at right angles from the same end of R. The resultant of XL and XC is found by subtracting XLfrom XC. This resultant represents the value of X.
Thus: X = XC – XL = 20 ohms – 10 ohms
= 10 ohms
Note: If inductive reactance is smaller than the capacitive reactance and is therefore subtracted from the capacitive reactance.
These two examples serve to illustrate an important point: when capacitive and inductive reactance are combined in series, the smaller is always subtracted from the larger and the resultant reactance always takes the characteristics of the larger.
- Given XL = 10 Ω, XC = 20 Ω, R = 40 Ω, calculate the impedance.
- 40Ω B. 41.2Ω C. 56Ω D. 45.3Ω
Given f = 1MHz, L = 100μH, C = 0.0002μF
- Calculate for inductive reactance
- 352Ω B. 702Ω C. 628Ω D. 245Ω
- Calculate for capacitive reactance
- 801Ω B. 235Ω C. 769Ω D. 745Ω
- Now assume you have a circuit containing a 100 – µH inductor in series with a .0002-µF capacitor, and operating at a frequency of 1 MHz. What is the value of the resultant reactance in this case?
- 168Ω B. 200Ω C. 265Ω D. 158Ω
- As with capacitive reactance, the voltage across the inductor is given by
- IXL B. IXC C. IXR D. IXZ
Join Discussion Forum and do your assignment: Find questions at the end of each lesson, Click here to discuss your answers in the forum
For advert placement/partnership, write email@example.com